HENAN ZHONGCHUANG PURE EP EUIPMENT CO.,LTD

As a  Filter Accessories And Equipment Factory , let us explain the consequences of incorrect placement of the filter press of the frame filter press. The pressure of the plate and frame filter press is insufficient. The filter plate and the filter cloth must be under strong pressure to realize the closed filter chamber structure. When the pressure is insufficient, the pressure applied to the filter plate is less than the pressure of the filtrate. Naturally, The filtrate will naturally be able to penetrate from the gap. When the edge of the Plate and Frame Jack Compacting Filter Press is damaged, even if it is slightly raised, even if one side wears frequently, and then it is contacted with another filter plate, the formed filter chamber will penetrate regardless of the pressure. In this case, we judge from the leakage point that the penetration of the filter plate is generally large and may even be sprayed. Plate and Frame Hydraulic Filter Press  is incorrectly p...

Filter Press Supplier   would like to share the installation method of the plate and frame filter press with you: Plate And Frame Filter Press 1. Design the pre-buried hole according to the size of the foot provided by the supplier, using two grouting methods. 2. There should be enough space around the filter press for easy operation and maintenance. 3. The  Plate And Frame Filter Press  should be placed horizontally on the floor, and the rear top plate should be fixed on the foundation with the foot screw. (Note: the bottom screw is generally only fixed to the rear top plate. Because the pull-drying has a certain downward bending due to the pressure of the plate frame. When the filter press is pressed, the pull-drying is straightened, resulting in a small displacement. If the two ends are fixed at the same time, which may cause the pressure to not be tight or damage the frame.) 4. The material and specifications of the  filter cloth   are det...

Friends who often use  Plate And Frame Filter Press , some people think that the scrap filter machine has no use, it can be sold as waste, which is not the case. The filter press is also disfigured to varying degrees, some scrapping degree The filter press can be reused. A large part of the lightly discarded filter press is only some parts scrapped. It only needs to be replaced with scrapped parts. If it is scrapped, it is really scrapped. There is no need to reuse it again. How to distinguish the scrapping degree of the filter press?  Filter Press Accessories Supplier  analyzes the scrap level of used filter presses: 1: Filter cloth and filter plate scrap: The model of the feed pump can be adjusted to check whether the pressure of the hydraulic station is abnormal, and replace the scraped filter cloth and filter plate in time. 2: The girders of the rack are broken or deformed and cannot be repaired or replaced. Otherwise, an accident will not be worth the loss...

We know that the Plate And Frame Filter Press allows the turbid filter to enter the filter press and become a clear liquid that flows out of the device. So how much do you know the specific principle of the plate and frame filter press? As a  Filter Press Supplier , let's take a look at it. 1. The filtrate is first pumped into the water inlet pipe by the feed pump, and the feed pump gradually increases the filtrate of the water inlet pipe, so that the filtrate enters the two water distribution pipes under high-pressure conditions. 2. The water distribution pipe is connected to the two inlet flanges above the Plate And Frame Filter Press, so that the filtrate enters the two distribution pipes above the filter plate of the plate and frame filter press, and the distribution pipe has The filter plates are extruded one by one, and on one side of the uniform direction of each filter plate, there are channels or grooves leading to the central recess of the filter plate. In this way...

As a supplier of  Chamber Filter Press , we continue to share with you the reasons why the Membrane Filter Press has a lower moisture content. In the rest of the Membrane Filter Press filter plate, a two-layer diaphragm plate is used to splicing the welded structure. There is a space between the two layers. There is a channel in the closed space, which can be connected with the high-pressure gas outside the filter press. The liquid is connected such that when the passage is opened, the high-pressure gas or liquid passes into the filter plate so that the pressure inside the filter plate is greater than the pressure outside the filter plate so that the diaphragm plates on both sides of the filter plate expand under internal pressure. The outer protrusion makes the middle of the original filter plate in the Membrane Filter Press filter room larger, and the corresponding filter cake is also smaller in the middle, so that the moisture in the filter cake can be further reduced under t...