The Reason Why the Filter Press Has a Slurry Leakage Phenomenon

Is the filter leakage occurring in the filter press because of adjusting the relief valve? As a Filter Press Supplier, let's analyze it together.
Membrane Filter Press does not maintain pressure, diaphragm filter press often occurs in the phenomenon of slurry leakage: improper adjustment or damage of the relief valve; oil leakage inside the valve; cylinder seal ring damage; leakage outside the pipeline; electromagnetic reversing valve is not in place (general It is because of this); the plunger pump is damaged (two because of this); there is not enough, check the level gauge.
The Membrane Filter Press uses a proportional valve. The hydraulic system has a wide range of problems and it is difficult to check. It needs to be checked step by step. If the oil is not clean, the hydraulic oil has impurities, the one-way valve core is worn out or the plunger oil pump is in the middle of the fault, and the signal of the proportional valve is disturbed, the diaphragm filter press will not be kept under pressure. The cylinder O-ring generally has a normal service life of 2-3 years. It is recommended to replace the cylinder seal first.
Membrane Filter Press
Membrane Filter Press
High Pressure Membrane Filter Press: The installation position of the mud device is too high, and it is not possible to adjust the position of the mud. Partial blockage of the mud shovel causes uneven local mud and needs to be cleaned to clear the blockage. The local wear of the loach is seriously caused, and the effect of the local sludge filtration is greatly reduced. After entering the pressing area, it still has a strong fluidity and needs to replace the damaged loach. The uneven wiper wears uneven surface and the wave is wavy, so that the mud is uneven in this area and needs to be replaced.

评论

发表评论

此博客中的热门博文

How To Choose Filter Cloth?

图片
The choice of  filter cloth  is very important for the filtration effect. The filter cloth plays a key role in the use of the filter press. Its performance is good or bad, and the correctness of the selection directly affects the filtering effect. The most common filter cloth currently used is a filter cloth made of synthetic fibers. According to the material, it can be divided into polyester, vinylon, polypropylene, nylon and so on. In order to achieve the interception effect and the filtration speed are ideal, in the selection of the filter cloth, it is also necessary to select according to the particle size, density, chemical composition and filtration process conditions of the slurry. Due to the difference in materials and methods of weaving, the strength, elongation, gas permeability and thickness of the filter cloth are different, which affects the filtering effect. In addition, the filter media also includes cotton woven fabrics, non-woven fabrics, screens, filter ...
阅读全文

Precautions for Using the Plate Frame Filter Press in Summer

图片
In summer, the temperature is high and the humidity is high. Many machines and equipment are overloaded due to overheating of the machine during operation, and the filter press is no exception. When using Plate and Frame Filter Press in summer, it is important to pay attention to the operating state of the plate and frame filter press to prevent damage caused by overload operation from affecting the filter press. So, what should you pay attention to during use?  Plate Frame Filter Press Factory  to explain to you. First, we pay attention to the hydraulic system. Since the equipment will repeatedly pressurize the filter plate during the working process, the hydraulic system will work frequently, withstand the huge pressure on the filter plate, the weather is hot, and the hydraulic device is easily overheated. Since the hydraulic unit itself is a highly enclosed component, some simple cooling methods are not ideal for hydraulic systems. Therefore, when using the Plate and Fra...
阅读全文

What is The Working Principle Of Filter Press

图片
A  Filter Press  is most commonly used to dewater sludge Made from industrial wastewater treatment plants. Filter Press Manufacturers  tell you the first stage of dewatering in a filter press is chemical conditioning. This is normally achieved by dosing a polymer into a mixed sludge storage tank upstream of the filter press. The flocculant will bind the sludge particles to larger flocs that are thicker and easier to dewater from the press. The slurry is then introduced through the center of the press where it fills the chambers between the plates. The pressure forces the liquid through the  Filter Cloth , whilst solids are retained between the plates. The filtrate flows between ridges in the plates to the corners where it discharges. The stages are as follows: 1. The chamber is empty, but has been sealed closed by the hydraulic ram. The press is ready to receive wet solids. 2. The wet solids are fed into the c...
阅读全文